6020B Hydraulic Shovel

6020B Hydraulic Shovel

When we invited our customers to help us design the first of our “Next Generation” Cat® hydraulic shovels, they gave us three top priorities: Make it safe, keep it simple and make it reliable. We responded by developing the Cat 6020B, which delivers the simplicity and versatility you desire, with valuable modern design features that set it apart from the competition.

The 6020B offers class-leading visibility and a cab designed for comfort, safety and efficiency. A walk-through and exchangeable power module contributes to easier serviceability. The 6020B is 25% more fuel efficient than other shovels in its class, delivering efficiency and cost advantages. And the proven C32 engine meets emission standards without the need for DEF, saving time and cost during maintenance.

Request a Quote

Engine Output - SAE J19951040hp

Bucket Payload23.8ton (US)

Operating Weight253.8ton (US)

NoteSpecifications shown above apply to a Backhoe configuration. A frontless configuration is also available.

Standard Bucket Capacity15.7yd³

Batteries (12V each) - In Series/Parallel Installation630 Ah – 24V

Components (3)9 LED high-brightness working flood lights: – 7 for working area
– 2 for rear end

Batteries (12V each)6 × 210 Ah

Components (1)Emergency stop buttons inside cab, accessible from all seating locations, and engine module

Components (2)Additional ground-level emergency stop

System Voltage24V

Battery Isolation Relaysmanual lockable disconnect switch and automatic disconnect relay

Components (6)1 beacon lamp on cab roof

Components (5)7 LED service lights

Components (4)2 LED high-brightness access flood lights

Features (2)Variable electronically controlled flow of oil through cooler and fan speed

Oil Flow of Cooling Pumps211gal/min

Diameter - Fan4.92ft

Features (1)Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running

Features (3)Superior cooling efficiency to ensure optimum oil temperature

Components (5)Full sized trainer seat with safety belt and work table

Internal Dimensions of Cab - Width5.33ft

Components (7)Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant

Components (9)Roller blinds

Components (11)Additional emergency ladder in close proximity to emergency escape window

Internal Dimensions of Cab - Length7.32ft

Components (8)Windshield with parallel intermittent wiper/washer

Components (2)Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests

New BCS Features (1)Robust instrument panel including large (254 mm/10 in) color touch screen

New BCS Features (3)Graphical data logging

New BCS Features (4)Fault memory capabilities

Operator's Eye Level (approximate)18.04ft

New BCS Features (2)On-screen troubleshooting assistance

Components (10)Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated

New BCS Features (5)USB, Lan (TCP/IP) and CAN BUS interfaces for data export

Components (3)Safety switch in operator's seat for automatic motion shutdown

Internal Dimensions of Cab - Height6.79ft

Components (1)Large cab floor window with removable grating for easy cleaning

Components (4)Joystick integrated in adjustable seat armrest

New Board Control System (BCS) Features:Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system

Components (6)Auxiliary fold-away seat with safety belt for 3rd person

Swing RingTriple-race roller bearing with sealed internal gearing

Maximum Swing Speed4.9r/min

Swing Drive2 compact planetary transmissions with axial piston motors

Parking BrakeWet multiple-disc brake, spring-loaded/hydraulically released

Features (2)All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system

Features (1)Open swing circuit with auto slow down when joysticks in neutral

Track Pads - Each Side45

Components (1)Forged double-grouser track pads

Components (6)Audible travel alarm

Bottom Rollers - Each Side8

Travel Speed - 1st Stage - Maximum0.68mile/h

Components (4)Fully hydraulic self-adjusting track tensioning system with accumulator

Components (5)Automatic hydraulic retarder valve to prevent overspeed on downhill travel

Parking BrakesWet multiple disc brake, spring loaded/hydraulically released

Travel Speed - 2nd Stage - Maximum1.49mile/h

Gradeability - Travel DrivesApproximately 54%

Components (3)All running surfaces of sprockets, idlers, rollers and track chain links hardened

Maximum Tractive Force265860lbf

Travel Drives - Each Side1 planetary transmission with 2 two-stage axial piston motors

Components (2)Chain links connected by hardened pins and bushings

Support Rollers - Each Side3

Type (3)System condition and failures displayed by Board Control System

Capacity - Grease Barrel54gal (US)

Type (1)Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control

Type (2)Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing

Type (5)Float valve for boom down function

Type (2)High-tensile steel with solid steel castings at pivot areas

Type (3)Boom and stick stress-relieved after welding

Type (1)Boom and stick torsion-resistant with welded box design

Type (4)Catwalks with rails at boom

Buckets Equipped With– Special liner material covering main wear areas inside and outside
– Lip shrouds
– Wing shrouds
– Heel shrouds

Standard Track Pads2.62ft

Operating Weight507500lb

Ground Pressure31.9psi

Maximum Swing Oil Flow216gal/min

Maximum Pressure - Attachment4495psi

Filters (4)Pressure filters (6 μm) for servo circuit

Electronic Pump Management Contains (3)Automatic return of main pumps to zero flow

Features (2)Cooling of pump transmission gear oil

Maximum Pressure - Travel4495psi

Maximum Pressure - Swing - Acceleration4495psi

Filters (3)Full-flow filters (10 μm) for cooling return circuit

Electronic Pump Management Contains (2)Dedicated circuit pump allocation

Maximum Total Oil Flow621gal/min

Filters (2)Full-flow filters (10 μm) for complete return circuit

Main Pumps6 × variable swash plate pumps

Filters (1)Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump

Electronic Pump Management Contains (4)Automatic rpm reduction of engine speed during working breaks

Filters (5)Transmission oil filter (40 μm)

Electronic Pump Management Contains (5)Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature

Electronic Pump Management Contains (1)Electronic load limit control

Features (1)Pressure cut-off function for all main pumps

Total Volume of Hydraulic Oil925gal (US)

Hydraulic Tank Capacity740gal (US)

Maximum Pressure - Swing - Deceleration5080psi

Equipped With (3)Indicator light for hydraulic tank full

Equipped With (1)Quick couplings for: – Diesel fuel
– Engine coolant
– Pump transmission gear oil
– Engine oil (oil pan)
– Hydraulic oil

FeaturesCentralized service area accessible from ground level.

Equipped With (2)Cat jump-start socket

Maximum Tearout Force146125lb

Maximum Breakout Force164050lb

Maximum Digging Reach52.17ft

Maximum Digging Depth26.57ft

Maximum Digging Height45.6ft

Operating Weight254ton (US)

Bucket Payload24Sh Ton

Standard Bucket Capacity - Backhoe (Heaped 1:1)15.7yd³

Gross Power - SAE J19951040hp

Engine ModelCat C32 ACERT

Net Power - SAE J13491032hp

Gross Power - SAE J19951040hp

Net Power - ISO 92491037hp

Net Power - SAE J13491032hp

EmissionsMeets China Nonroad Stage III emissions standards, equivalent to Tier 2

Components (1)Cat NOx reduction system

Components (7)Two-stage fuel filter

Components (3)MEUI™-C fuel system

Alternator275A

Bore5.71in

Components (4)Hydraulically driven radiator fan with variable electronically controlled fan speed

No. of Cylinders12

Displacement1959in³

Fuel Tank Capacity951gal (US)

Components (5)Micro processed engine management

Rated Speed1,800 min-1 (1,800 rpm)

AspirationTurbocharged and air-to-air aftercooled

Components (2)Dual Diesel Oxidation Catalysts (DOCs)

Components (8)Additional high-capacity water separator including electric priming pump

Components (9)Large fuel tank allows for 24 hour machine operation

Components (6)Heavy-duty air filters

Maximum Altitude without Deration2925 m (9,600 ft) – above sea level (a.s.l.)

Stroke6.38in

Make and ModelCat C32 ACERT

Components (3)Heavy-duty air filters

Components (4)Two-stage fuel filter

Fuel Tank Capacity951gal (US)

No. of Cylinders12

Components (2)Micro processed engine management

Displacement1959in³

Maximum Altitude without Deration3622 m (11,884 ft) – above sea level (a.s.l.)

Bore5.71in

Components (1)Hydraulically driven radiator fan with variable electronically controlled fan speed

Stroke6.38in

AspirationTurbocharged and air-to-air aftercooled

Components (5)Additional high-capacity water separator including electric priming pump

Rated Speed1800 min-1 (1,800 rpm)

Alternator275A

Make and ModelCat C32 ACERT

Components (6)Large fuel tank allows for 24 hour machine operation

Gross Power - SAE J19951033hp

Net Power - ISO 92491024hp

Net Power - SAE J13491019hp

EmissionsMeets Tier 4 Final and Stage V emissions standards

Net Power - SAE J13491019hp

Gross Power - SAE J19951033hp

Engine ModelCat® C32 ACERT™

Optional

Cold-weather package

Lube fast fill port

Optional

Redundant HVAC system

Camera system

Cat MineStar Health ready

Optional

Rough terrain undercarriage protection kit including belly plate and rear plumbing guard

Dirt scraper on swivel connection

Track pad width 1000 mm (3 ft 3 in)

Optional

LED work lights on boom

Optional

Additional buckets available, based on application, through your local Cat dealer

CONTACT US

REQUEST A QUOTE

Complete this form to get a quote on the equipment you are interested in.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    What You Get: A phone call from a rep or agent. A cost estimate for your machine or the project. An in-person consultation if necessary.