Nominal Payload Class (100%)61ton (US)
Top Speed - Loaded41.6mile/h
Note (2)* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations.
Maximum Working Payload (110%)67.1ton (US)
Note (1)Capacity with Dual Slope body – no liner.
Body Capacity - SAE 2:146.8yd³
Target Payload (100%)61ton (US)
Maximum Allowable Payload (120%)*73.2ton (US)
Engine ModelCat® C27
Rated Engine Speed1800r/min
Gross Power - SAE J1995775HP
Net Power - SAE J1349719HP
Net Power - ISO 9249762HP
Net Power - 80/1269/EEC762HP
Bore5.4in
Stroke6in
Displacement1648in³
Note (1)Power rating applies at 2,000 rpm when tested under the specified condition for the specified standard.
Engine Power - ISO 14396764HP
Peak Torque - Speed1200r/min
Net Torque3148ft-lb
Note (3)No engine derating required up to 3048 m (10,000 ft) for Tier 4/Stage V.
Note (2)Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F).
Struck35.13yd³
Heaped (SAE 2:1)*46.76yd³
Note (2)* ISO 6483:1980.
Note (1)Contact your local Cat dealer for body recommendation.
Struck34.33yd³
Note (2)* ISO 6483:1980.
Heaped (SAE 2:1)*46.41yd³
Note (1)Contact your local Cat dealer for body recommendation.
Front Axle - Empty53%
Front Axle - Loaded35%
Rear Axle - Empty47%
Rear Axle - Loaded65%
Forward - 16.6mile/h
Forward - 29.3mile/h
Forward - 312.6mile/h
Forward - 416.8mile/h
Forward - 522.8mile/h
Forward - 630.7mile/h
Forward - 741.6mile/h
Reverse8.7mile/h
NoteMaximum travel speeds with standard 24.00R35 (E4) tires.
Differential Ratio3.64:1
Planetary Ratio4.80:1
Total Reduction Ratio17.49:1
Brake Surface - Front257in²
Brake Surface - Rear9497in²
Brake StandardsISO 3450:2011
Fuel Tank210gal (US)
Cooling System45gal (US)
Differential - Final Drives38gal (US)
Steering Tank9.5gal (US)
Steering System - Including Tank14gal (US)
Torque Converter - Transmission System - HRC18gal (US)
Crankcase24gal (US)
Brake Hoist System85gal (US)
Brake/Hoist Hydraulic Tank46.5gal (US)
Pump Flow - High Idle118gal/min
Relief Valve Setting - Raise2502psi
Relief Valve Setting - Lower500psi
Body Raise Time - High Idle10s
Body Lower Time - Float14s
Body Power Down - High Idle14s
Rear axle - Oscillation8.1°
Empty Loaded Cylinder Stroke Rear5.8in
Empty Loaded Cylinder Stroke Front9.2in
Note (1)Productive capabilities of the 773G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Note (2)Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
Standard Tire24.00R35 (E4)
FOPS StandardsFalling Object Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
ROPS StandardsRollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
Sound Standards (3)Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.
Sound Standards (2)The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 86 dB(A).
Sound Standards (1)The operator Equivalent Sound Pressure Level (Leq) is 76 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with t
Turning Diameter - Front77.1ft
Steering StandardsSAE J1511 FEB94 ISO 5010:1992
Steer Angle31°
Turning Circle - Clearance Diameter85.6ft
Maximum Gross Vehicle Weight226501lb