C18 ACERT Land Mechanical Drilling Engine

Maximum Rating700BHP

EmissionsEPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Displacement1100in³

Minimum Rating575BHP

Bore5.7in

Stroke7.2in

Rated Speed2100r/min

AspirationTurbocharged-Aftercooled

Governor and ProtectionADEM A3

Engine Weight - Net Dry2807lb

Rotation from Flywheel EndCounterclockwise

Oil Change Interval250

Flywheel and Flywheel HousingSAE No. 0 or SAE No. 1

Flywheel Teeth136 (SAE 0), 113 (SAE 1)

Minimum Cooling System - Engine Only13.2gal (US)

Length54.7in

Width36.2in

Height49.5in

Standard

Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection

Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection

Optional

Air cleaners

Air lines

Standard

Electronic governing, PTO speed control

Programmable ratings

Cold mode start strategy

Automatic altitude compensation

Power compensation for fuel temperature

Programmable low and high idle and TEL

Electronic diagnostics and fault logging

Engine monitoring and protection system (speed, temperature,pressure)

J1939 Broadcast (diagnostic, engine status, and control)

Standard

Thermostats and housing — outlet vertical

Jacket water pump — gear-driven, centrifuga

RH front water pump inlet

All plugs/fittings are STOR for lines gp water

Optional

Radiator

Fan drive with radiator packages

Fan height instructions

Vee belts

Aftercooler lines with Caterpillar installed radiator

Single turbo configuration rear-facing exhaust

Single turbo configuration rear-facing exhaust

Aftercoooler lines

Suction fan adapters

Blower fan adapter

Blower fan

Suction fan

Fan belt

Coolant level sensor

Dry charge coolant conditioners

Standard

Exhaust manifold — dry

Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo

Dual turbo — exhaust elbow, dry 203 mm (8 in)

Optional

Turbo exhaust connection

Flexible fittings

Elbows, flange, clamp, pipes

Exhaust adapters

Manifold

Mufflers

Standard

See Mandatory Options

Standard

Electronic unit injector

Fuel filter, secondary, mid-mount (LH 2 micron high performance)

Fuel transfer pump, LH front

Fuel priming pump, LH mid-mount

Fuel sample valve, mounted on fuel filter base.

Standard

Crankcase breather — rear valve cover

Oil cooler — RH (dual)

Oil filter — RH, LH

Oil pan — front sump

Oil dipstick — LH front

Oil pump

Optional

Oil pans

Drain and cover

Oil level gauge

Remote oil filters

Oil filters

Lubricating oils

Standard

Front support (shipping only)

Optional

Structural steel base

Front and rear engine support

Standard

Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width

Hydraulic pump drive, SAE A, 11-tooth

Optional

Rear enclosed clutches

Hydraulic pump drives

Hydraulics gear pumps

Clutch supports

Crankshaft pulleys

Standard

Vibration damper

Paint — Cat yellow

Lifting eyes

Automatic variable timing, electronic

Electronic installation kit 70-pin connector (connectors, pins,sockets)

Standard

Throttle position sensor

Single turbo only — exhaust system (front or rear)

Flywheel housing or rear PTO

Primary filter/water separator

Optional

Air compressor governor

Expansion chambers

Optional

Charging alternators

Alternator mountings

Alternator wiring

Circuit breakers and mountings

Alternator belt guard

Optional

Flexible fuel lines

Fuel filter location

Fuel cooler

Water separator

Optional

Gauges and instrument panels

Optional

Air shutoff

Optional

Air starting motors

Air pressure regulator

Air silencer

Start switch

Electric starting motors — 12V, 24V

Battery sets – 24V

Battery cable and rack

Starting aids

Optional

Transmission water lines